How to make a tree house with your own hands: we build a hut

How to make a tree house with your own hands: we build a hut

We are searching data for your request:

Forums and discussions:
Manuals and reference books:
Data from registers:
Wait the end of the search in all databases.
Upon completion, a link will appear to access the found materials.

In the world there are such things that literally every child dreams of. This is not only a game console or a bicycle, the child also wants to have a place where he can feel like a master. Therefore, many kids are always looking for a certain headquarters or game base. So why don't they ease the task? Try to build a tree house for your child, and the joy of the baby will have no boundaries.

Of course, for the construction of such a house will require considerable effort, but they will not be wasted. It is only necessary to show diligence, carefully think through and prepare everything so that the design of the house is safe and reliable for the child.

DIY tree house for children

The project described below for the construction of a treehouse for children was developed taking into account safety, maximum preservation of trees and reliability of structures. This design is completely autonomous, so it can be installed absolutely anywhere, even where there are no trees. The house is based on a universal triangular structure, in principle, there is no need to dig support pillars deep into the ground - if there is a rocky, flat area, the house will hold well on it. Of course, the resulting construction will not be small, it simply cannot be built in one day, but it will be interesting for children, especially if they are involved in the work.

Drawing blanks

It is necessary to begin work with the manufacture of a triangular frame.

  1. At an angle of 30 degrees, it is necessary to cut off one end of each front leg of the future home, as shown in the drawing. After that, the legs are screwed to the beam with 10 cm screws. It is best to do this process on the ground.
  2. Next, temporarily fix the corner ends in the center of the support. The ends are fixed, and the crossbar is fixed on top of her legs.
  3. Next, you need to drill a through hole through the legs and the central pillar. Carefully make a recess at the ends of the hole for the washer, nut and bolt head. Then tighten all the bolts.
  4. Assemble the rear frame.
  5. Now you need to prepare the plumb line and level. You will also need an assistant to install the frame. This stage is the most difficult, but if you have a flat area, the process will be much easier.
  6. It is also necessary to determine which of the four foot positions is the lowest. To do this, you can use a long straight board and level.
  7. The assembly begins with this very leg, fixed in such a way that it becomes sheer. Be sure to check that the beam is located at the required height and is evenly fixed.
  8. The same thing is done with the rest of the legs. Once again, you need to check that everything is fixed exactly, perpendicular and parallel.
  9. After that, diagonal crosses are attached to the legs and fixed with screws.
  10. Next, you need to drill two holes on all legs and tighten with bolts.
  11. In conclusion, two more holes of smaller diameter at the intersection of the brackets must be pulled together with 10 cm bolts.

Assembly of the site and stairs

Next, you can start assembling the site of the future home.

  1. First of all, it is necessary to strengthen all the corners of the frame with a pad using metal brackets.
  2. Nail the hanging anchors to the rear and front connecting beams.
  3. After that, it is possible to cut the boards for the floor of 2.5 m. It is also temporarily necessary to screw one board in the middle of the frame, and then begin to lay the boards starting from the back.
  4. Before fixing the extreme boards, you need to cut a hole for the hatch. At the ends of the boards, it is advisable to pre-drill holes so that the wood does not crack during fastening.
  5. When you get to the center, you need to remove the time bracket. Make the connecting element from the boards so that it is located between the beams.
  6. Fasten plywood and the remaining floorboards to the bottom.
  7. To fasten cruciform brackets to the hind legs of the future home, remove the extra length.

Next, you need to start assembling the stairs:

  1. Screw the two steps to the beams, which should be located at the same angle as the legs to secure the ladder.
  2. Beams attach to the platform.
  3. Screw the steps to the stringers with 10 cm screws, starting from the top.
  4. On the right side of the stairs, screw the railing into the stringer.

House assembly

After that, you can proceed directly to the assembly of the house:

  1. First, on the ground, you need to collect the lining of the side walls.
  2. After that, it is necessary to screw one wall through the bottom plate to the site.
  3. Assemble the rear wall and mount it on the platform.
  4. Make sure it fits snugly against the bottom plate of the side wall.
  5. After this, you need to install in parallel another side wall.
  6. Attach temporary brackets to the inside of the back wall.
  7. Mount the front panel without a bar and rafters, they are added after installation.
  8. Connect all the parts together, install two halves of the wall on the site.
  9. Fasten them with staples so that the wall is quite stable.
  10. Attach the sheathing and make sure that all the cutouts for the rafters are located in the right place.
  11. Cut the front panel so that it fits around the rafters.
  12. Next, you need to fasten it to the door frame and rafters.
  13. Remove all curly braces.
  14. Attach boards to the rafters starting from the front edge of the house roof.
  15. Trim the side panels and fasten to the rafter shanks.
  16. Install window frames and door jamb.

Railing Installation

The final step will be the installation of railings.

  • The railing must be screwed to the handrails and round off all the sharp corners available.
  • Nail or fasten the balusters to the beam, as well as to the bottom of the handrails. In this case, the distance between them should be no more than 10 cm.
  • In conclusion, you must install the safety circuit with a latch.

It must be remembered that all children will check the strength of the house, so you do not need to save on equipment and purchase low-quality materials.

We figured out how to make a tree house with our own hands. The interior of the orphanage you can think of yourself, discuss this issue with your child. You can install a bunk bed there, put a table, benches, shelves and much more.

Scheme of building a hut on the ground

For the construction of a hut or halabud, you need to choose a suitable place. In no case should such a hut be installed in narrow gorges, on the banks of rivers, at the bottom of canyons. Regardless of whether the hut will be erected in Russia or in another country, floods, sudden showers or a leash can occur everywhere. The main options for the location of the hut:

  • Hut in a mountain forest. For this area, it is best to select for the construction of an attached type of structure. This means that one of the walls of halabud or two walls will be made of stone or wood - part of the rock. In this case, try to avoid precipitation. Therefore, huts are not recommended to be located in hollows with obvious traces of water flows. The rest of the rules for the construction of a hut are the same as for a regular tent. The entrance to the hut should be located on the opposite side of the peak. On the perimeter it is necessary to make a ditch so that during the rain water flows into it.
  • Hut in the flat forest. In a flat forest, you can build an in-depth, classic or side hut. At the same time, a place is chosen, focusing on the weather. In cold weather without rain, the hut is placed in an in-depth place, which will be a temporary refuge for him. During rains, these structures must be located on an elevated place.

The structure of the hut by its type:

  • Classical. The construction of this type is made in the form of a fireplace for cooking. During construction, two poles or branches are installed vertically. The third is laid on them in a horizontal position. Dressing is done with improvised means, stems, flexible branches, vines. But there are several more installation options. For example, two poles or even branches that need to be cut with a knife, set to each other at an angle at the exit of the structure and the back wall of the hut at a distance of about 2 m. After that, the main pole is laid horizontally on it. If a wigwam is being constructed, then in this case the poles are laid in a circle at an angle to each other in the form of a bonfire, as a support for them, you can use a living growing tree.
  • The attached. This can also be attributed to the lodge, which will be created on the basis of poles resting on a rock in a mountainous area. The walls are made in this case, as in the specified classic hut.
  • In-depth. This type of hut is similar to the classic one, but located in a hollow, it is something between a hut and a dugout. In this case, only the top is covered.

In the forest, in the absence of the usual sleeping bags, folding beds, inflatable mattresses and bedding, you must be able to adapt to such conditions. There are two types of floor arrangement in a hut: with and without a hearth. As a rule, in the cool time of the year, it is necessary to protect the walls of the hut and the logger from sparks of the hearth. Therefore, it is laid out in the center, limited to stones, earth is poured between the stones, and a quarantine zone of about 20 cm is made around the hearth. A fallen tree, represented by last year's leaves with branches, shoots, is laid on the ground. You can also use extra clothes, polyethylene or tarpaulin material for this.

Treehouse for children in stages

When building a treehouse, everything is also quite simple and understandable. If two adjacent trees are located on a summer cottage, then a good structure can be built between them. This will require a minimum of time and building materials. Before making a treehouse, It is necessary to stock up on the following tools and devices:

  • Bolts.
  • Plywood sheets: two of them 10 mm thick, one 20 mm thick.
  • Bars with dimensions of 50x150 mm and 50x100 mm.
  • Circular saw or hacksaw.
  • Galvanized nails.
  • Birch bark.
  • Ruberoid.

As the base of the hut, two boards 50x150 mm are used. In this case, they must be attached to two thick trees. It is pretty simple. It is only necessary that the diameters of the tree trunks are about 20 cm. After that, the bottom with side walls, as well as the triangles for the brackets, must be cut out from the plywood sheet. This will require a little scrupulousness and patience.

Further, from pre-prepared and sawed in half-timber bars, it is necessary to collect triangular sidewalls. After that, they are bolted together. Then it is necessary to connect the assembled triangular sidewalls with a ridge beam. Its cross section should be 50x100 mm.

These sidewalls are connected to two bars, which are located below. Using the brackets, attach the resulting frame to the supporting boards, the cross section of which is 50x150 mm. They must be pre-attached to the trees.

After that, the bottom is taken, which is cut from plywood. Holes for nails are drilled in it. Then the bottom is nailed to the lower bars and logs with galvanized nails with large hats.

Next, you need to think about the construction of skylights and roofs. It is recommended to use a multi-layer roof for this. This will ensure the reliability of the hut. The first layer uses plywood with a thickness of approximately 10 mm. The second layer may consist of roofing material or glassine. For the third layer, birch bark is ideal.

Having become acquainted with the description of the manufacture of a house and a hut, everyone for himself decides how to build a structure for his child from improvised materials. The main thing in this case is to remember that the house for your child, first of all, must be safe.

Video, Sitemap-Video, Sitemap-Videos